Veto Pro Pac Tech Pac Blackout (with Panels)
Veto Pro Pac Tech Pac Blackout (with Panels)
The Tech Pac Blackout is a blacked-out tool backpack for tool storage based on our Tech Pac but with Veto Pro Pac’s V-Swap™ system that COMES WITH FRONT AND BACK removable TOOL and METER pocket panels which are also exchangeable. You can purchase additional Meter, Tool and other panels as desired, including a Laptop Panel that can turn the bag into a tool bag/laptop bag, and the Laptop Panel can go in the front or the back, flat rubber panel for Bulk Storage, a Modular panel, Utility Panel, and Folio panel. Includes V-Swap™ Tool Panel and Meter Panels, V-Swap™ Laptop, Folio, Utility, Modular, and Bulk Storage Panels Sold Separately.
NOTE: THIS BAG COMES WITH THE TOOL AND METER PANEL. YOU DO NOT HAVE TO SELECT ANY PANELS FOR THE BAG TO COME WITH THE TOOL AND METER PANELS THOUGH YOU MAY PURCHASE ADDITIONAL PANELS TO OFFER A VARIETY OF CONFIGURATIONS.
PRODUCT SPECIFICATIONS:
- Height (H): 19.5” (49.5cm)
- Width (W): 13" (33cm)
- Depth (D): 10" (25cm)
- Handle Height (HH): 22" (56cm)
- Weight (empty): 12.25lbs (5.5kg)
- Internal Volume: 1550in3 (25L)
- Max Payload: 50lbs (23kg)
MAXIMIZED TOOL STORAGE CAPACITY:
- Vertical Tool Pockets: 46 interior and exterior tool pockets of various sizes
- Upper Pockets (Front Side) Designed For Extra Tool Capacity
- Swap-Out Tool Panels- Front and Back Tool Panels are removable and exchangeable
- Laptop Panel Available as an accessory (must be purchased separately).
- 8" Electrical Tape Strap
- 2 Storage Bays- 4 Storage Platforms
- Manifold Gauge and Hose Storage Pocket
- D-Rings: 4 large and 5 small
- Outside Mounted Stainless Steel Tape Clip Holder
RUGGED MATERIALS AND CONSTRUCTION:
- LOAD TESTED: PULLED TO DESTRUCTION AT 830 POUNDS (Handle failed); Hook failed at 200 Pounds
- Weatherproof Base: 3mm Injection Molded Polypropylene
- Tactical All Black Polyester Body Fabric (phthalate free) & Interior Construction - Gray Pockets For Better Visibility
- Quick Release Metal Hasp: Allows Easy Access to Rear Storage Bay
- Internally Stored Aluminum Hook to Hang Bag
- Over-Molded Ergonomic Grip
- Padded EVA Thermoformed, Ergonomic Back Padding
- Metal Shoulder Strap Sliding Buckles
- D-Rings: Powder Coated Steel
- Rivets: Marine Grade Rivets
- Stitching: Industrial Strength Double Nylon Stitching
OTHER FEATURES:
- Includes Front Tool Panel and Back Tool & Meter Panel, Laptop Panel Sold Separately
- Metal YKK® Locking Zippers
- Magnetic Screw Catcher
- Warranty: 5 Years (see Veto warranty terms and conditions)
VETO PRO PAC TOOL BAGS PRODUCT CARE AND MAINTENANCE
Keep the Zippers Clean & Lubricated
Over time, dirt and grit will “clog” the zipper coils preventing them from staying closed. To keep this from happening, clean and lubricate your zippers twice a year (more often if you work on a job site with a high amount of airborne debris). To clean the coils: Scrub them with soapy water; a tooth brush works very well. After scrubbing the coils, blow them out with an air hose to dislodge any other fine grit that didn’t dislodge with the brush. To lubricate the coils: Apply a silicone spray, beeswax or a zipper lubricant.
Protect the Zippers From Sharp Objects and/or Excessive Heat
Any sharp object or heat source is capable of permanently damaging the zippers. Once a zipper coil is cut or singed the zipper will not function and in most cases is not repairable. Most of the cut zipper coils we see are the result of sharp tools stored inside the bag with the sharp side facing up. Make sure to keep the sharp edges of your tools facing down in your bag and away from the zipper coils.
Don’t Overstuff the Bag
Overstuffing your tool bag will very likely cause significant stress on the zippers that is above and beyond what the bag was built for and will eventually cause the zipper(s) to separate. If you have to work hard to close your zipper(s), your tool bag is most likely overstuffed… proceed with caution!